Alastair Posted July 7, 2022 Share Posted July 7, 2022 Ok i have both the V1 and V2 Inceptions, however both of them appear to be suffering the same issue where the fire button's are getting stuck. Ive tried Cleaning them out but to no avail, ive also tried lubricating the buttons with Wd40 and even a little PG but they still are sticking. Both the shells are stab wood/hybrid stab wood Any help/suggetions would be much appricated. Quote Link to comment Share on other sites More sharing options...
Michael Goodman Posted July 10, 2022 Share Posted July 10, 2022 On 7/7/2022 at 6:18 PM, Alastair said: Ok i have both the V1 and V2 Inceptions, however both of them appear to be suffering the same issue where the fire button's are getting stuck. Ive tried Cleaning them out but to no avail, ive also tried lubricating the buttons with Wd40 and even a little PG but they still are sticking. Both the shells are stab wood/hybrid stab wood Any help/suggetions would be much appricated. That sucks! You know that's not your fault it's because he free hands the shells! Ugh! He actually screwed Jai on that Mod and caused a shit ton of headaches, problems and royally fucked Jai and lied to Jai, he said he knew exactly what and how Jai wanted and reassured Jai he could go it easily! But, instead he did what he wanted more than what Jai wanted him to do and fucked it up royally on that mod and shells! And you know all those jealous P.O.S.'s and trashy people have been waiting for a long time seething, frothing and foaming at the bit so bad and for so long just for ANY type of flaw no matter small or insignificant it was they were ready to pounce and gang up on Jai and blaming Jai for something he had no control over and Jai didn't manufacture it he designed it but, they didn't hear that or cared about it! All they cared about was what are all the shitty retarded comments they can post after watching Mike's Vapes review and him shaking the holy shit out of it just to make the batteries rattle and to cause shit! Sorry for the rant. Ok about your buttons and shell, First off use wax not liquid lubricant, it's much better and if your shell is made of stab wood wax won't make the grains of the wood swell where liquid lube will and also it stays on better too even on resin shells. If that doesn't help then you are going to either lightly sand the buttons or sand the holes where the buttons go through the mod. Really that's pretty much all you can do now. Just remember, it probably won't take much sanding so go slow and check frequently. And this is some the problems that guy made because he wanted to make them ALL by hand and not using a mock up mod to make them all the exactly tj same like Brandon does. I hope that helps. 1 Quote Link to comment Share on other sites More sharing options...
Alastair Posted August 25, 2022 Author Share Posted August 25, 2022 On 7/10/2022 at 10:06 AM, Michael Goodman said: That sucks! You know that's not your fault it's because he free hands the shells! Ugh! He actually screwed Jai on that Mod and caused a shit ton of headaches, problems and royally fucked Jai and lied to Jai, he said he knew exactly what and how Jai wanted and reassured Jai he could go it easily! But, instead he did what he wanted more than what Jai wanted him to do and fucked it up royally on that mod and shells! And you know all those jealous P.O.S.'s and trashy people have been waiting for a long time seething, frothing and foaming at the bit so bad and for so long just for ANY type of flaw no matter small or insignificant it was they were ready to pounce and gang up on Jai and blaming Jai for something he had no control over and Jai didn't manufacture it he designed it but, they didn't hear that or cared about it! All they cared about was what are all the shitty retarded comments they can post after watching Mike's Vapes review and him shaking the holy shit out of it just to make the batteries rattle and to cause shit! Sorry for the rant. Ok about your buttons and shell, First off use wax not liquid lubricant, it's much better and if your shell is made of stab wood wax won't make the grains of the wood swell where liquid lube will and also it stays on better too even on resin shells. If that doesn't help then you are going to either lightly sand the buttons or sand the holes where the buttons go through the mod. Really that's pretty much all you can do now. Just remember, it probably won't take much sanding so go slow and check frequently. And this is some the problems that guy made because he wanted to make them ALL by hand and not using a mock up mod to make them all the exactly tj same like Brandon does. I hope that helps. Sry thought i had replied to this earlier. I had to gingerly prise the fire buttons off each mod and sand them untill they did not stick anymore. The V1 didnt take much however the V2 took a lot more and it seems the plastic pin used to secure the button had snapped approx half way up which was probably half of the issue. Quote Link to comment Share on other sites More sharing options...
Recommended Posts